Home > Return Code > Return Code 0099

Return Code 0099

Verify that all DC voltages applied to the printer control board are correct. Error Code: 133 Description: +5 VDC not present on carrier detect. Inspect the note transport make sure all belts are on track and there is no currency jammed in the transport or exit areas. Inspect for jammed currency in the feed path and at the Exit sensor. check over here

Recommended Action: This error code is generated when the number of reject events exceeds 37 events. Recommended Action: See the recommended action for error code 144. Recommended Action: Check data and power connections to the dispenser device. Replace the dispenser is the error persists.

Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. S10A - 04 - NOT ENOUGH REAL STORAGE FOR SPACE IN SQA SUBPOOL. ONE OF THE FOLLOWINF OCCURRED: - A DATA EXTENT CONTROL BLOCK (DECB) WAS USED TWICE. - MULTIPLE READS OR WRITES WERE ISSUED, BUT ONLY THE LAST READ OR WRITE WAS CHECKED.

  • PDF EPUB Login Please log in to export content.
  • If the error clears, put the cash dispenser in service. 5.
  • Clear any jammed currency. 2.
  • Error Code: 207 Description: SPED not detected.
  • S02C - AN ERROR OCCURRED IN JES2 SUPPORT OF AN FSS ADDRESS SPACE.
  • Error Code: 205 Description: SPED keypad reported tamper condition.

Inspect the note feeders and note qualifier for damage. Clear all errors and test the dispenser with a live transaction. When this is done, the terminal will operate normally until it is completely out of paper. ACCEPTABLE TYPES ARE ADD, DELETE, VERIFY, AND PURGE.

Remove any jammed notes. 3. Error Code: 158 Description: Format command to electronic journal failed. Make sure it is seated at the main board at J15 and at the printer control board at CN6. S2F3 - JOB WAS BEING EXECUTED WHEN SYSTEM FAILURE OCCURRED - A SYSTEM RESTART WAS PERFORMED S300 - AN ERROR WAS DETECTED WHEN AN I/O OPERATION WAS REQUESTED; - EITHER THE

S213 - DSCB NOT FOUND; I/O ERROR IN READING OR WRITING DSCB. Recommended Action: This error code is produced when the single reject event counter exceeds 50 reject events or the bundle reject event counter exceeds 250 notes. Inspect the feed path for jammed currency. S14F - THE ROUTINE ATTEMPTED TO EXECUTE THE STATUS MACRO INSTRUCTION FOR OTHER THAN THE STOP, STOP SYNCH, OR START FUNCTION AND WAS NOT IN SUPERVISOR KEY (0-7).

IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S202 OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S202-RC)** S202 - 00 - THE CONTROL PROGRAM FOUND AN INVALID Menu Contents Menu Documentation Legal Notice My Account Sign In Why CA Products Education & Training Services & Support Partners CA Top Secret® for z/VM - 12.1 Documentation powered by DocOps Error code 320 will not put the cash dispenser "Out of Service. Recommended Action: This error code occurs when documents are requested from a cassette that is not present or is not open.

Give an example for High severity and Low Priority ? http://supportcanonprinter.com/return-code/mdt-return-code-1.html The cash dispenser may be turned OFF, or the telephone line is shared with some other device that connects to the line before the cash dispenser. Documentation Legal Notice Contents | Home Messages and Return Codes z/VM Messages TSS0001 to TSS0099 Last update July 18, 2014 Use the following search feature to find a specific message or S0B0 - 0C - ATTEMPTING TO READ A BLOCK NOT YET WRITTEN.

Search returned no results. Error Code: 157 Description: Format command to electronic journal failed. S137 - 30 - A LABEL VIOLATED THE PUBLISHED STANDARD FOR THE LABEL, AND THE LABEL VALIDATION EXIT REQUESTED OPEN/EOV TO REJECT THE VOLUME. http://supportcanonprinter.com/return-code/eza1735i-std-return-code-27550-error-code-00002.html Test the TDM-100 by completing several Test Dispenses.

Recommended Action: This error code is returned by the dispenser when the number of notes in one or more of the cassettes is below a preset level, indicating the low level S0C7 - DATA EXCEPTION - DECIMAL DATA IS INCORRECT OR IMPROPERLY OVERLAPPED OR NOT VALIDLY INITIALIZED. If the error clears, put the cash dispenser in service. 6.

The maximum number of notes that can be dispensed from the dispenser during a transaction is defaulted to fifty.

All rights reserved. Recommended Action: See the recommended action for error code 144. Host hung up. S233 - 20 - THE USER SUPPLIED A DCB ADDRESS AND THE DCB IS NOT OPEN, OR THE DCB ADDRESS IS INVALID.

If the error clears, put the cash dispenser in service. 5. Make sure it is connected to CN1 on the printer control board. Clear the error. have a peek at these guys Verify that the diverter moves freely and is not binding.

It will be display as the hexadecimal number "30" when running the dispenser with the NMD test software. Recommended Action: Error code valid only for units with SPED keypad device installed. S03B - ISAM DATASET TO BE PROCESSED, BUT NOT CREATED OR ITS DCB NOT CLOSED AFTER CREATION. The most probable cause is either mechanical or electrical failure of the note diverter in the note transport module.

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK A MINIMUM NUMBER OF VSM CELLS (IN LSQA) DURING LOCAL CELL POOL EXPANSION. Error occurred Loading... If the error does not repeat again, complete a live dispense to verify the note diverter moves the currency to the exit position.

If the status clears and the return code are normal place the cash dispenser in service. Error Code: 18 Description: OVERFLOW Possible Cause: Received more characters, than expected after request causing modem buffer overflow. Clean and verify the operation of the exit sensor. Clear all error and purge the dispenser using the purge command. 3.

TOO MANY TRACKS WERE SPECIFIED FOR CYLINDER OVERFLOW. The recommended capacity is 1850 documents. S301 - AN ECB SPECIFIED IN A WAIT MACRO ALREADY HAD ITS WAIT FLAG ON.